T & G, tongue and groove - A joint made by a tongue (a rib on one edge of a board) that fits into a corresponding groove in the edge of another board to make a tight flush joint. Typically, the sub-floor plywood is T & G.

Tab - The exposed portion of strip shingles defined by cutouts.

Tail Beam - A relatively short beam or joist supported in a wall on one end and by a header at the other.

Take Off - The material necessary to complete a job.

Taping - The process of covering drywall joints with paper tape and joint compound.

T bar - Ribbed, "T" shaped bars with a flat metal plate at the bottom that are driven into the earth. Normally, used chain link fence poles, and to mark locations of a water meter pit.

Teco - Metal straps that are nailed and secure the roof rafters and trusses to the top horizontal wall plate. Sometimes called a hurricane clip.

Tee - A "T" shaped plumbing fitting.

Tempered - Strengthened. Tempered glass will not shatter nor create shards, but will "pelletize" like an automobile window. Required in tub and shower enclosures and locations, entry door glass and sidelight glass, and in a windows when the windowsill is less than 16" to the floor.

Terra Cotta - A ceramic material molded into masonry units.

Thermoply ™ - Exterior laminated sheathing nailed to the exterior side of the exterior walls. Normally ¼ " thick, 4 X 8 or 4 x 10 sheets with an aluminumized surface.

Three-dimensional Shingles - Laminated shingles. Shingles that have added dimensionality because of extra layers or tabs, giving a shake-like appearance. May also be called "architectural shingles".

Threshold - The bottom metal or wood plate of an exterior doorframe. Generally they are adjustable to keep a tight fit with the door slab.

Time and Materials Contract - A construction contract which specifies a price for different elements of the work such as cost per hour of labor, overhead, profit, etc.
A contract, which may not have a maximum price, or may state a 'price not to exceed'.

Tinner - Another name for the heating contractor.

Tip Up - The downspout extension that directs water (from the home's gutter system) away from the home. They typically swing up when mowing the lawn, etc.

TJI or TJ - Manufactured structural building component resembling the letter "I". Used as floor joists and rafters. I-joists include two key parts: flanges and webs. The flange or from of the I joist may be made of laminated veneer lumber or
dimensional lumber, usually formed into a 1 ½" width. The web or center of the I-joist is commonly made of plywood or oriented strand board (OSB). Large holes can be cut in the web to accommodate ductwork and plumbing waste lines. I-joists are available in lengths up to 60'' long.

Toenailing - To drive a nail in at a slant. Method used to secure floor joists to the plate.

Top Chord - The upper or top member of a truss.

Top Plate - Top horizontal member of a frame wall supporting ceiling joists, rafters, or other members.

Tread - The walking surface board in a stairway on which the foot is placed.

Treated Lumber - A wood product, which has been impregnated with chemical pesticides such as CCA (Chromated Copper Arsenate) to reduce damage from wood rot or insects. Often used for the portions of a structure, which are likely to be in contact with soil and water. Wood may also be treated with a fire retardant.

Trim (plumbing, heating, electrical) - The work that the "mechanical" contractors perform to finish their respective aspects of work, and when the home is nearing completion and occupancy.

Trimmer - The vertical stud that supports a header at a door, window, or other opening.

Truss - An engineered and manufactured roof support member with "zig-zag" framing members. Does the same job as a rafter but is designed to have a longer span than a rafter.

Tub Trap - Curved, "U" shaped section of a bath tub drain pipe that holds a water seal to prevent sewer gasses from entering the home through tubs water drain.